Direct Fuel Injector Cleaning Service in Jamaica

Our direct injection fuel injector cleaning service includes before and after results and comes with a written report.

Only $2000 + GCT per GDI injector.

Replacement of GDI O rings, seals and filter baskets will be at an additional cost.


 

Call us today at 876-507-3059  for more information on our fuel injection cleaning service in Jamaica. We can clean your direct injectors and save you money! We service injectors for people islandwide!Direct Injection Fuel Injectory

Engine manufacturers are switching to Direct Injection to meet emissions standards, better performance and greater fuel economy. GDI or Gasoline Direct Injection is the way forward.

What is Direct Injection?

Instead of delivering the fuel via an injector in the intake track before the intake valve, GDI or gasoline direct injected engines inject a very fine mist of fuel directly in to the combustion chamber hence the name Direct Injection.  Direct injectors operate at fuel pressures that vary between 450 — 3000 Psi. To achieve these pressures, the gasoline is pressurized by a high pressure fuel pump that is mechanically driven and electronically controlled.

Why use Gasoline Direct Fuel Injectors?

GDI or Gasoline Direct Injection enables the engine to operate at a stratified charge combustion, described by most of the vehicle manufacturers as an Ultra Lean Burn mode, giving a much improved fuel efficiency, great engine torque and reduced Exhaust Emission levels at low load.

With the sequential firing GDI systems, the  injectors only opens to a maximum of 7mS. As the fuel requirement increases, the injector remains at 7mS and the pump pressure increases to meet the demand, allowing the injector to open and close quickly and efficiently. No more “Duty Cycle” as we have known it. These engines use expensive high specification injectors, with Hitachi, Bosch, Denso and Siemens being the major suppliers.

Call us now at 876-507-3059 to speak with us about our fuel injector cleaning services in Jamaica

Direct Fuel Injection and Carbon Buildup!

Direct  injectors are prone to carbon build up and are affected by the hostile environment in the combustion chamber as well as ethanol, hydrocarbons and additives which forms part of today’s fuels that we are be sold in Jamaica.

direct injection injectors - Google Search

 

Because there is no cleaning agent, such as gasoline, present to clean the valves from any debris the current drawback from direct injection systems in 4 cycle engines is the buildup of carbon and dirt behind the intake valves and ports . Engines start losing performance after 40,000 - 45,000 miles and the only remedy on some models is costly because it requires removal of the cylinder head to remove the dirt buildup from the intake valves and ports. 

  

The importance of direct injection fuel injector cleaning in Jamaica.

direct injection fuel injector cleaningDepending on the engine requirements, this style of injectors can have varying types of spray patterns.  All direct injectors will atomize a much smaller fuel droplet size than a normal MPI injector. Conventional injector would have a fuel droplet size of +/- 165 micron, where some GDI injectors would produce a fuel droplet of only +/- 65 micron. To maintain this kind of atomization it is important to include direct injection fuel injector cleaning in your maintenance schedule.

 

GDI Fuel Distribution and Atomization

Fuel Distribution and Atomization is equally critical to the engine’s performance, fuel economy and emission outputs. A clogged direct injector or a set of dirty direct fuel injectors will cause a range of problems and in some instances even severe engine damage.

Our testing equipment allows us to critically examine direct injectors for correct electronic operation in response to changes in mS, RPM and proper atomization as well as the proper cleaning techniques that will allow us to restore your GDI injectors to original specification.

Most direct injection fuel injectors are difficult and time consuming to remove and re-fit; would you fit a set of injectors without ensuring they are working correctly?

Insist your dealer/mechanic/technician send your dirty clogged or leaking direct fuel injectors to us for cleaning before they attempt to replace them with expensive new ones. If the injector does not perform up to spec or we can not clean them, we will not charge you for the time spent on that injector. 

Why flow testing direct injectors at 72.5 psi or 5 Bar

Many customers want to know why we do not test direct injectors at operating pressure.

  1. It is dangerous
  2. The equipment is very expensive
  3. We can determine flow rate at lower pressure by applying math.
  4. We can determine and develop a good understanding of spray pattern and atomization at lower pressures

Direct injection fuel injector manufacturers usually will supply test pressure in MPa (Megapascal) and the flow rate in g/s (Grams per second)

1 MPa =  10 Bar = 145.0377 psi

1g/s = 7.937 lb/hr

1 lb/hr = 10.5 cc/min

A manufacturers  direct injector has the following specification: @ 20 MPa delivering 24 g/s. This means that.

Up to 24  g/s of fuel will be delivered at an operating pressure of 20 MPa and in layman’s terms this means that:

24 x 7.937 = 190.48 lb/hr of fuel will be delivered at a pressure of 20 x 145.0377 = 2900.75 psi.

= 190.48 lb/he @ 2900.75 psi

To calculate the amount of fuel the direct injector will flow at 72.5 psi we will use a mathematics formula:

which gives us: 30.1148 lb/ hr

Now that we have determined the amount the injector should flow at 72.5 psi we can proceed with the flow testing and measure the testing result against the calculated result.

Acronyms associated with Direct Injectors

GDI = Gasoline Direct Injection (Mitsubishi GDI)
FSI = Fuel Stratified Injection (VW)
SCi = Smart Charge injection (Ford)
HPi = High Precision Injection (BMW)
JTS = Jet Thrust Stoichiometric (Alfa Romeo)
GTDI = Gasoline Turbocharged Direct Injection (Ford)
IDE = Injection Direct Essence
SIDI = Spark Ignition Direct Injection (Holden)

 

Jamaica's Best Fuel Injector Cleaning Service

Symptoms

Symptoms of clogged/dirty injectors

  • hard starting
  • rough idle
  • throttle “tip-in” hesitation
  • pre-ignition (sometimes heard as that ‘pinging sound’)
  • poor overall performance
  • decreased gas mileage

How long does it take to clean injectors?

It takes approximately 15-25 minutes to clean 4, 6 or 8 injectors.

What makes our service better?

When we clean your injectors we also replace O rings, seals and filter baskets with new parts. O rings and seals are known to dry rot and the filter baskets are prone to rust due to water being absorbed because of the ethanol in the fuel.

Additional Articles

Contact us


Complete form below to contact us

If you have any questions feel free to complete form and we will reply as soon as possible. If you give us your number we will give you a call.

ADDRESS
Fuel Injector Jamaica
53 Hagley Park. Kingston 10. Jamaica
Kingston, St. Andrew JMAAW08
Jamaica

PHONE
876-507-3059

EMAIL
[email protected]